manualshive.com logo in svg

HP 5800, Command Reference Manual, Page: 213 / 396

Share
Download
HP 5800 Command Reference Manual Download Page 213

 

204 

Field Description 

Flag 

Current status of the label  
0x0001 (BGP_VPLS_LB_NOT_SENTTO_VPLS) 
0x0002 (BGP_VPLS_LB_SENTTO_VPLS) 
0x0004 (BGP_VPLS_LB_SELECTED) 
0x0008 (BGP_VPLS_LB_ASBR_TNLDOWN) 
0x0010 (BGP_VPLS_LB_FROM_RR_IBGP) 
0x0020 (BGP_VPLS_LB_FROM_RR_EBGP) 
0x0040 (BGP_VPLS_LB_FROM_IBGP) 
0x0080 (BGP_VPLS_LB_FROM_EBGP) 
0x0085 (BGP_VPLS_LB_NOT_SENTTO_VPLS | 

BGP_VPLS_LB_SELECTED | 
BGP_VPLS_LB_FROM_EBGP) 

LB Offset 

Label offset value 

LB Size 

Label size 

LB Base 

Initial label of the label base 

LB NewBase 

New label base 

RefCount 

Label reference count 

MED Cost 

value 

AS Path 

AS path of the route 

MTU 

Maximum transmission unit at Layer 2 

Encap Type 

Encapsulation type 

 

display mac-address vsi 

Description 

Use the 

display mac-address vsi

 command to display the MAC address table information of a specified 

VPLS instance or all VPLS instances. 
Related commands: 

vsi

; 

mac-address 

(

Layer 2—LAN Switching Command Reference

)

.

 

Syntax 

display mac-address vsi

 [ 

vsi-name 

] [ 

blackhole 

| 

dynamic

 | 

static 

] [

 count

 ] [ 

|

 { 

begin

 | 

exclude

 | 

include

 } 

regular-expression 

] 

View 

Any view 

Default level 

1: Monitor level 

Parameters 

vsi-name

: Specifies the name of the VPLS instance, which is a case-insensitive string of 1 to 31 characters. 

Hyphens (-) are not allowed. 

blackhole

: Specifies the black hole MAC forwarding entries. 

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments