HP 5800 Command Reference Manual Download Page 195

Page: 195 / 396

186

Parameters

frequency

seconds

: Specifies reoptimization frequency, ranging from 1 to 604,800 seconds. The default

is 3600 seconds, or 1 hour.

Examples

# Enable reoptimization, setting the reoptimization (automatic rerouting) frequency to 43,200 seconds (12

hours).

<Sysname> system-view

[Sysname] interface tunnel 0

[Sysname-Tunnel0] mpls te reoptimization frequency 43200

mpls te reoptimization (user view)

Description

Use the

mpls te reoptimization

command to start reoptimizing all reoptimization-enabled TE tunnels.

Syntax

mpls te reoptimization

View

User view

Default level

2: System level

Parameters

None

Examples

# Start reoptimizing all reoptimization-enabled TE tunnels.

<Sysname> mpls te reoptimization

mpls te resv-style

Description

Use the

mpls te resv-style

command to set the resource reservation style for the MPLS TE tunnel.

Use the

undo

mpls te resv-style

command to restore the default.

The default resource reservation style is SE.
You may configure FF and SE only when the signaling protocol is set to RSVP-TE.

Syntax

mpls te resv-style

{

}

undo

mpls te resv-style

View

Tunnel interface view

Default level

2: System level

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

HP 5800, Command Reference Manual, Page: 195 / 396

Search results

Summary of Contents for 5800

Reviews: