manualshive.com logo in svg

HP 5800, Command Reference Manual, Page: 188 / 396

Share
Download
HP 5800 Command Reference Manual Download Page 188

 

179 

Parameters 

absolute 

value

: Assigns an absolute metric to the TE tunnel for path calculation. The 

value

 parameter 

takes an integer ranging from 1 to 65,535. This value is directly used for path calculation.  

relative 

value

: Assigns a relative metric to the TE tunnel for path calculation. The 

value

 parameter takes 

an integer ranging from –10 to +10. The default is 0. The cost of the IGP path must be added to this 

relative metric before it can be used for path calculation. 

Examples 

# Assign MPLS TE tunnel 0 a relative metric of –1 for enhanced SPF calculation in IGP.  

<Sysname> system-view 

[Sysname] interface tunnel 0 

[Sysname-Tunnel0] mpls te igp metric relative -1 

mpls te igp shortcut 

Description 

Use the 

mpls te igp shortcut

  command  to  enable  IS-IS  or  OSPF  to  consider  the  MPLS  TE  tunnel  in  its 

enhanced SPF calculation when the tunnel is up. If you do not specify an IGP protocol, the command 

applies to both OSPF and IS-IS.  
Use the 

undo mpls te igp shortcut

 command to restore the default. 

By default, IGP does not consider MPLS TE tunnels in its enhanced SPF calculation. 
The 

mpls te igp shortcut

 command cannot be used together with the 

mpls te igp advertise

 command. 

Syntax 

mpls te igp shortcut

 [ 

isis

 | 

ospf 

] 

undo mpls te igp shortcut 

View 

Tunnel interface view 

Default level 

2: System level 

Parameters 

isis

: Sets the IGP protocol to IS-IS. 

ospf

: Sets the IGP protocol to OSPF. 

Examples 

# Enable OSPF and IS-IS to consider TE tunnel 0 in enhanced SPF calculation when the tunnel is up. 

<Sysname> system-view 

[Sysname] interface tunnel 0 

[Sysname-Tunnel0] mpls te igp shortcut 

mpls te link administrative group 

Description 

Use the 

mpls te link administrative group

 command to configure the link administrative group attribute. 

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments