manualshive.com logo in svg

HP 5800, Command Reference Manual, Page: 179 / 396

Share
Download
HP 5800 Command Reference Manual Download Page 179

 

170 

Examples 

# Enable RSVP message retransmission on VLAN-interface 1, setting the increment value delta to 2 and 
the initial retransmission interval to 1000 milliseconds. 

<Sysname> system-view 

[Sysname] interface vlan-interface 1 

[Sysname-Vlan-interface1] mpls rsvp-te timer retransmission increment-value 2 retransmit-

value 1000 

mpls te 

Description 

Use the 

mpls te

 command to enable MPLS TE. 

Use the 

undo mpls te

 command to disable MPLS TE. 

By default, MPLS TE is disabled.  
When performed in MPLS view, the 

mpls te

 command enables MPLS TE globally and its 

undo

 form 

disables MPLS TE and removes all CR-LSPs.  
When performed in interface view, the 

mpls te

 command enables MPLS TE on an interface, and its 

undo

 

form disables MPLS TE and removes all CR-LSPs on the interface.  
Enable MPLS TE globally before you enable MPLS TE on an interface. 

Syntax 

mpls te 
undo mpls te 

View 

MPLS view, interface view 

Default level 

2: System level 

Parameters 

None 

Examples 

# Enable MPLS TE globally in MPLS view. 

<Sysname> system-view 

[Sysname] mpls lsr-id 1.1.1.9 

[Sysname] mpls 

[Sysname-mpls] mpls te 

# Enable MPLS TE on VLAN-interface 1. 

<Sysname> system-view 

[Sysname] interface vlan-interface 1 

[Sysname-Vlan-interface1] mpls 

[Sysname-Vlan-interface1] mpls te 

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments