manualshive.com logo in svg

HP 5800, Command Reference Manual, Page: 174 / 396

Share
Download
HP 5800 Command Reference Manual Download Page 174

 

165 

Enable RSVP-TE before you configure the keep multiplier.  
Related commands: 

mpls rsvp-te timer refresh

.

 

Syntax 

mpls rsvp-te keep-multiplier

 

number

 

undo mpls rsvp-te keep-multiplier 

View 

MPLS view 

Default level 

2: System level 

Parameters 

number

: Specifies the keep multiplier, ranging from 3 to 255. 

Examples 

# Set the keep multiplier to five. 

<Sysname> system-view 

[Sysname] mpls 

[Sysname-mpls] mpls rsvp-te keep-multiplier 5 

mpls rsvp-te reliability 

Description 

Use the 

mpls rsvp-te

 

reliability

 command to enable the reliability mechanism of RSVP-TE—the 

Message_ID extension mechanism.  
Use the 

undo mpls rsvp-te

 

reliability

 command to disable the reliability mechanism. 

Syntax 

mpls rsvp-te reliability 
undo mpls rsvp-te reliability 

View 

Interface view 

Default level 

2: System level 

Parameters 

None 

Examples 

# Enable the reliability mechanism of RSVP-TE on VLAN-interface 1. 

<Sysname> system-view 

[Sysname] interface vlan-interface 1 

[Sysname-Vlan-interface1] mpls rsvp-te reliability 

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments