HP 5800 Command Reference Manual Download Page 167

Page: 167 / 396

158

View

System view

Default level

2: System level

Parameters

pathname

: Specifies the name of an explicit path for a tunnel, which is a string of 1 to 31 characters.

disable

: Disables explicit routing.

enable

: Enables explicit routing.

Examples

# Create an explicit path named path1 and enter its view.

<Sysname> system-view

[Sysname] explicit-path path1

[Sysname-explicit-path-path1]

list hop

Description

Use the

list hop

command to display information about a specific node or all nodes on the explicit path.

Syntax

list hop

[

ip-address

]

View

Explicit path view

Default level

2: System level

Parameters

ip-address

: Specifies the IP address of a node on the explicit path. If you do not specify an IP address,

information about all the nodes on the explicit path is displayed.

Examples

# Display information about all nodes on an MPLS TE explicit path.

<Sysname> system-view

[Sysname] explicit-path path1

[Sysname-explicit-path-path1] list hop

Path Name : path1 Path Status : Enabled

1 1.1.1.9 Strict Include

2 2.2.2.9 Strict Exclude

modify hop

Description

Use the

modify hop

command to change the IP address of a node on the explicit path.

By default, the changed IP address is included on the explicit path, and its next hop is a strict node.

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

HP 5800, Command Reference Manual, Page: 167 / 396

Search results

Summary of Contents for 5800

Reviews: