HP 5800 Command Reference Manual Download Page 164

Page: 164 / 396

155

Configuration:

Neighbor Ip Address: 100.0.0.2

Cost : -10

Cost Type : Relative

Hold time : 10s

Table 72

Command output

Field Description

Interface

Tunnel interface address and name

Type

Approach to automatic route advertisement: IGP shortcut or
forwarding adjacency

Neighbor ID

Remote neighbor ID

State

State: up or down

display tunnel-info

Description

Use the

display tunnel-info

command to display information about tunnels.

Syntax

display tunnel-info

{

tunnel-id |

all

statistics

} [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

tunnel-id

: Specifies a tunnel ID, ranging from 1 to FFFFFFFE. If you specify a tunnel, only information

about this tunnel is displayed.

all

: Display information about all tunnels.

statistics

: Displays statistics about tunnels.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see the

Fundamentals Configuration Guide.

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, which is a case-sensitive string of 1 to 256 characters.

Examples

# Display information about all tunnels.

<Sysname> display tunnel-info all

Tunnel ID Type Destination

------------------------------------------------------

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

HP 5800, Command Reference Manual, Page: 164 / 396

Search results

Summary of Contents for 5800

Reviews: