HP 5800 Command Reference Manual Download Page 161

Page: 161 / 396

152

Field Description

BackUpBW Backup bandwidth

Route Pinning

Route pinning function

Retry Limit

Maximum number of setup retries

Retry Interval

Retry interval

Reopt

State of the reoptimization function

Reopt Freq

Reoptimization interval

Back Up Type

Backup path type

Back Up LSPID

Backup LSP ID

Auto BW

State of the automatic bandwidth adjustment function

Auto BW Freq

Automatic bandwidth adjustment interval

Min BW

Lower limit for automatic bandwidth adjustment

Max BW

Upper limit for automatic bandwidth adjustment

Current Collected BW

Bandwidth information collected

Interfaces Protected

FRR protected interfaces

VPN Bind Type

Type of the binding, VPN or ACL

VPN Bind Value

Value of the binding, the VPN instance name or ACL number

Car Policy

Whether CAR policy is enabled

Tunnel Group

Whether the tunnel is the primary tunnel or backup tunnel in the
group.

Primary Tunnel

Tunnel ID of the primary tunnel. If the tunnel is the primary tunnel, – is
displayed for this field.

Backup Tunnel

Tunnel ID of the backup tunnel. If the tunnel is the backup tunnel, – is
displayed for this field.

Group Status

Status of the group. Displayed as - if no protection group is
configured.

Oam Status

OAM defect detection status. – means OAM is not enabled.

display ospf mpls-te

Description

Use the

display ospf mpls-te

command to display TE LSAs in the LSDB.

Syntax

display ospf

[

process-id

]

mpls-te

[

area

area-id

] [

self-originated

] [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

HP 5800, Command Reference Manual, Page: 161 / 396

Search results

Summary of Contents for 5800

Reviews: