HP 5800 Command Reference Manual Download Page 140

Page: 140 / 396

131

Field Description

Ingress LSR ID

Ingress LSR ID, in the format of X.X.X.X.

Local LSP ID

Local LSP ID.

Next Hop

Next hop address, in the format of X.X.X.X.

Previous Hop

Previous hop address, in the format of X.X.X.X.

In Label

Incoming label.

Out Label

Outgoing label.

Send message ID

Instance of sent Message ID.

Resv Message ID

Instance of received Message ID.

Setup Prio

Session setup priority.

HoldPrio

Session hold priority.

Session Flag

Session flag (local protection policy, label, SE style).

ERO Information

Information about explicit routes.

L-Type

Explicit routing type: strict or loose.

ERO-IPAddress

IP address for an explicit route.

ERO-Prefix Len

Prefix length for an explicit route.

RRO Information

Information about route recording.

RRO-C Type

Type of route recording.

RRO-IP Address

IP address of recorded route in the format of X.X.X.X.

RRO-IPPrefixLen

IP prefix length of recorded route.

Sender Tspec Information

Information about sender's service specifications.

Token Bucket rate

Token bucket rate (in kbps), a traffic parameter.

Token Bucket size

Token bucket size, a traffic parameter.

Peak Data Rate

Peak data rate (in kbps), a traffic parameter.

Maximum packet size

Maximum packet size, a traffic parameter.

Minimum policed unit

Minimum policed unit, a traffic parameter.

Path message

Path message sent from the interface to the next hop at X.X.X.X.

Resource

Available when the RSVP flag is configured.

Graceful Restart State

State of GR: stale or normal. Displayed as --- when not supported by
the device.

display mpls rsvp-te request

Description

Use the

display

mpls rsvp-te request

command to display information about RSVP-TE requests on the

specified or all interfaces.

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

HP 5800, Command Reference Manual, Page: 140 / 396

Search results

Summary of Contents for 5800

Reviews: