Home
/
HP
/
5800
/
Command Reference Manual

HP 5800, Command Reference Manual, Page: 118 / 396

Share

Page: 118 / 396

HP 5800 Command Reference Manual Download Page 118

109

incoming-interface

interface-type interface-number

: Specifies an incoming interface by its type and

number.

in-label

in-label

: Specifies the incoming label, which can be 0, 3, or a value ranging from 16 to 1023.

Examples

# Configure a static LSP named

bj-sh

, taking the current LSR as the egress, VLAN-interface 2 as the

incoming interface, and 233 as the incoming label.

<Sysname> system-view

[Sysname] static-lsp egress bj-sh incoming-interface vlan-interface 2 in-label 233

static-lsp ingress

Description

Use the

static-lsp ingress

command to configure a static LSP taking the current LSR as the ingress.

Use the

undo static-lsp ingress

command to remove a static LSP taking the current LSR as the ingress.

If you specify the next hop when configuring a static LSP, and the address of the next hop is present in the
routing table, you also need to specify the next hop when configuring the static IP route.
The address of the next hop cannot be any local public network IP address.
Related commands:

display mpls static-lsp

,

static-lsp egress

, and

static-lsp transit

.

Syntax

static-lsp

ingress

lsp-name

destination

dest-addr

{

mask

|

mask-length

}

nexthop

next-hop-addr

out-label

out-label

undo static-lsp

ingress

lsp-name

View

System view

Default level

2: System level

Parameters

lsp-name

: Specifies the name for the LSP, which is a string of 1 to 15 characters.

destination

dest-addr

: Specifies the destination IP address of an LSP.

mask

: Specifies the mask of the destination IP address.

mask-length

: Specifies the length of the mask for the destination address, ranging from 0 to 32.

nexthop

next-hop-addr

: Specifies the next hop address.

out-label

out-label

: Specifies the outgoing label, which can be 0, 3, or a value ranging from 16 to 1023.

Examples

# Configure a static LSP named

bj-sh

to destination address 202.25.38.1/24, taking the current LSR as

the ingress, 202.55.25.33 as the next hop address, and 237 as the outgoing label.

<Sysname> system-view

[Sysname] static-lsp ingress bj-sh destination 202.25.38.1 24 nexthop 202.55.25.33 out-

label 237

«
...
116
117
118
119
120
...
»

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments