manualshive.com logo in svg

HP 5500 HI Series, Configuration Manual

The HP 5500 HI Series is a premium networking solution designed to elevate your organization's connectivity. Seamlessly configure and optimize your network settings with the comprehensive Configuration Manual available for free download from our website, empowering you to unlock the full potential of this cutting-edge product.

Share
Download
background image

 

77 

Authentication status 

VLAN manipulation 

A user in the 802.1X critical VLAN fails 
authentication because all the RADIUS 

servers are unreachable. 

The user is still in the critical VLAN. 

A user in the critical VLAN fails 802.1X 
authentication for any other reason than 
server unreachable. 

If an Auth-Fail VLAN has been configured, re-maps the MAC 
address of the user to the Auth-Fail VLAN ID. 

A user in the critical VLAN passes 802.1X 
authentication. 

Re-maps the MAC address of the user to the server-assigned 
VLAN.  
If the authentication server assigns no VLAN, re-maps the MAC 
address of the user to the default or user-configured PVID on the 

port.  

A user in the 802.1X guest VLAN or the 
Auth-Fail VLAN fails authentication because 

all the RADIUS server are unreachable. 

The user remains in the 802.1X VLAN or the Auth-Fail VLAN.  

A user in the MAC authentication guest 
VLAN fails 802.1X authentication because 

all the 802.1X authentication server are 

unreachable. 

The user is removed from the MAC authentication VLAN and 
mapped to the 802.1X critical VLAN.  

 

 

NOTE: 

The network device assigns a hybrid port to an 802.1X critical VLAN as an untagged member.  

 

Any of the following RADIUS authentication server changes in the ISP domain for 802.1X users on a port 

can cause the users to be removed from the critical VLAN: 

•

 

An authentication server is added to the ISP domain and the server is reachable. 

•

 

A response from a RADIUS authentication server is received.  

•

 

The RADIUS server probing function detects that a RADIUS authentication server is reachable.  

You can use the 

dot1x critical recovery-action reinitialize

 command to configure the port to trigger 

802.1X re-authentication when the port or an 802.1X user on the port is removed from the critical VLAN.  

•

 

If MAC-based access control is used, the port sends a unicast Identity EAP/Request to the 802.1X 
user to trigger authentication. 

•

 

If port-based access control is used, the port sends a multicast Identity EAP/Request to the 802.1X 

users to trigger authentication.  

ACL assignment 

You can specify an ACL for an 802.1X user to control its access to network resources. After the user 

passes 802.1X authentication, the authentication server, either the local access device or a RADIUS 

server, assigns the ACL to the port to filter the traffic from this user. In either case, you must configure the 

ACL on the access device. You can change ACL rules while the user is online. 

Configuration prerequisites 

•

 

Configure an ISP domain and AAA scheme (local or RADIUS authentication) for 802.1X users.  

Summary of Contents for 5500 HI Series





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 5500 HI Series

D-Link DES-1228/ME User Manual preview
DES-1228/ME
Brand: D-Link Pages: 267
D-Link DSL-504T Manual preview
DSL-504T
Brand: D-Link Pages: 99
D-Link DI-804V Datasheet preview
DI-804V
Brand: D-Link Pages: 5
D-Link DES-1210-08P Manual preview
DES-1210-08P
Brand: D-Link Pages: 15
D-Link AirPro DWL-6000AP Manual preview
AirPro DWL-6000AP
Brand: D-Link Pages: 65
D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 5
D-Link DSL-G2562DG Quick Start Manual preview
DSL-G2562DG
Brand: D-Link Pages: 2
Barco MatrixPRO-II DVI 16x16 User Manual preview
MatrixPRO-II DVI 16x16
Brand: Barco Pages: 43
Barco matrixpro-II Information Manual preview
matrixpro-II
Brand: Barco Pages: 5
TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Brand: TE Connectivity Pages: 236
D-Link DIR-853/EE Quick Installation Manual preview
DIR-853/EE
Brand: D-Link Pages: 83
Enginko MCF-LW06424 Operating Manual preview
MCF-LW06424
Brand: Enginko Pages: 19
I-O Wireless WBC11 User Manual preview
WBC11
Brand: I-O Wireless Pages: 55
Idis DR-8400 Installation Manual preview
DR-8400
Brand: Idis Pages: 31
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Brand: QNAP Pages: 51
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
Comet Labs 24-Port 1000BASE-T User Manual preview
24-Port 1000BASE-T
Brand: Comet Labs Pages: 44
Chaparral FS1310 User Manual preview
FS1310
Brand: Chaparral Pages: 96

Brands by name

Popular brands

Load more brands