manualshive.com logo in svg

HP 5500 HI Series, Configuration Manual

The HP 5500 HI Series is a premium networking solution designed to elevate your organization's connectivity. Seamlessly configure and optimize your network settings with the comprehensive Configuration Manual available for free download from our website, empowering you to unlock the full potential of this cutting-edge product.

Share
Download
background image

 

369

 

Configuring ARP attack protection 

The term "interface" in this chapter

 

collectively refers to VLAN interfaces and Layer 3 Ethernet interfaces. 

You can set an Ethernet port as a Layer 3 interface by using the 

port link-mode route

 command (see 

Layer 2

—

LAN Switching Configuration Guide

). 

Overview 

Although ARP is easy to implement, it provides no security mechanism and is vulnerable to network 

attacks. An attacker can exploit ARP vulnerabilities to attack network devices in the following ways: 

•

 

Acts as a trusted user or gateway to send ARP packets so the receiving devices obtain incorrect ARP 

entries.  

•

 

Sends a large number of destination unreachable IP packets to have the receiving device busy with 
resolving destination IP addresses until its CPU is overloaded. 

•

 

Sends a large number of ARP packets to overload the CPU of the receiving device. 

For more information about ARP attack features and types, see 

ARP Attack Protection Technology White 

Paper

. 

ARP attacks and viruses are threatening LAN security. This chapter introduces multiple features to detect 

and prevent such attacks. 

ARP attack protection configuration task list 

 

Task Remarks 

Flood prevention 

Configuring 
ARP 

defense 
against IP 

packet 

attacks 

Configuring ARP source 
suppression 

Optional. 
Configure this function on 
gateways (recommended). 

Enabling ARP black hole routing 

Optional. 
Configure this function on 
gateways (recommended). 

Configuring ARP packet rate limit 

Optional. 
Configure this function on access 
devices (recommended). 

Configuring source MAC address based ARP 
attack detection 

Optional. 
Configure this function on 
gateways (recommended). 

User and gateway 
spoofing prevention 

Configuring ARP packet source MAC address 
consistency check 

Optional. 
Configure this function on 
gateways (recommended). 

Configuring ARP active acknowledgement 

Optional. 
Configure this function on 
gateways (recommended). 

Summary of Contents for 5500 HI Series





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 5500 HI Series

N-Tron 700 Series User Manual & Installation Manual preview
700 Series
Brand: N-Tron Pages: 101
ZETR 25 Installation Manual preview
25
Brand: ZETR Pages: 2
CallDirect CD Series At Command Manual preview
CD Series
Brand: CallDirect Pages: 33
Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
NavigateWorx NR300 User Manual preview
NR300
Brand: NavigateWorx Pages: 71
Kontron 50099 067 User Manual preview
50099 067
Brand: Kontron Pages: 42
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Brand: impinj Pages: 60
Rasilient ApplianceStor 15MT User Manual preview
ApplianceStor 15MT
Brand: Rasilient Pages: 30
Maipu SM3100-9TC-AC Install Manual preview
SM3100-9TC-AC
Brand: Maipu Pages: 26
Buffalo BS-GS2008P Quick Setup Manual preview
BS-GS2008P
Brand: Buffalo Pages: 2
Ubiquiti UniFi AP PRO Quick Start Manual preview
UniFi AP PRO
Brand: Ubiquiti Pages: 20
Milesight Pro UR32 Quick Start Manual preview
Pro UR32
Brand: Milesight Pages: 15
TRENDnet TE100S8P - Fast Ethernet Switch (Spanish) Quick Installation Manual preview
TE100S8P - Fast Ethernet Switch
Brand: TRENDnet Pages: 11
Black Box LB9002A-SC-R3 Manual preview
LB9002A-SC-R3
Brand: Black Box Pages: 12
Honeywell Home LTEM-PA Installation And Setup Manual preview
LTEM-PA
Brand: Honeywell Home Pages: 36
Multitech ROUTE FINDER RFIPSC-1 Quick Start Manual preview
ROUTE FINDER RFIPSC-1
Brand: Multitech Pages: 54
Patton electronics 3196RC User Manual preview
3196RC
Brand: Patton electronics Pages: 93
H3C MSR 900 Quick Start Manual preview
MSR 900
Brand: H3C Pages: 46

Brands by name

Popular brands

Load more brands