manualshive.com logo in svg

HP 5400R zl2 Series, Nstallation And Getting Started Manual

Share
Download
HP 5400R zl2 Series Nstallation And Getting Started Manual Download Page 72

4-2

Replacing Components

Replacing Power Supplies

Repl

aci

ng Comp

one

nts

Replacing Power Supplies

If your HP 5400R zl2 Switch is configured with redundant power supplies, you 
will not suffer any loss of traffic or performance if a power supply fails. 
Replace the failed component as soon as possible. One of the Internal Power 
LEDs on the management module will blink simultaneously with the switch 
Fault LED indicating which power supply failed.

Although these procedures show the 6-slot chassis, the procedures are the 
same for the 12-slot chassis. 

To remove an AC power supply:

1.

Ensure the AC power supply is not plugged into an AC power source on 
the failed power supply.

2.

Using either a flat-bladed or Torx T-10 screwdriver loosen the retaining 
screws and remove the failed power supply.

Figure 4-1. Power supply removal

Summary of Contents for 5400R zl2 Series













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands