HP 3600 v2 Series Command Reference Manual Download

Page: 207 / 510

half-life-unreachable

: Specifies a half-life for suppressed routes from 1 to 45 minutes. By default, the

value is 15 minutes.

reuse

: Specifies a reuse threshold value for suppressed routes from 1 to 20000. A suppressed route

whose penalty value decreases under the value is reused. By default, the reuse value is 750.

suppress

: Specifies a suppression threshold from 1 to 20000. The route with a penalty value higher

than the threshold is suppressed. The default value is 2000.

ceiling

: Specifies a ceiling penalty value from 1001 to 20000. The value must be bigger than the

suppress

value. By default, the value is 16000.

route-policy-name

: Routing policy name, a case-sensitive string of 1 to 63 characters.

half-life-reachable, half-life-unreachable, reuse, suppres

s and

ceiling

are mutually dependent. Once

any one is configured, all the others should also be specified.

Description

Use

dampening

to enable BGP route dampening, configure dampening parameters, or both.

Use

undo dampening

to disable route dampening.

By default, no route dampening is configured.

The command dampens only EBGP routes rather than IBGP routes.

Related commands:

reset bgp dampening

reset bgp flap-info

display bgp routing-table

dampened

display bgp routing-table dampening parameter

, and

display bgp routing-table

flap-info

Examples

# In BGP view, configure BGP route dampening.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] dampening 15 15 1000 2000 10000

# In BGP-VPN instance view, configure BGP route dampening. (The VPN has been created.)

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpn-instance vpn1

[Sysname-bgp-ipv4-vpn1] dampening 15 15 1000 2000 10000

default ipv4-unicast

Syntax

default ipv4-unicast

undo default ipv4-unicast

View

BGP view

Default level

2: System level

Parameters

None

Description

Use

default ipv4-unicast

to enable the default use of IPv4 unicast address family for the peers that

are established using the

peer as-number

command.

195

Summary of Contents for 3600 v2 Series































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3600 v2 Series

Reviews:

Related manuals for 3600 v2 Series

Brands by name

Popular brands

HP 3600 v2 Series, Command Reference Manual

Search results

Summary of Contents for 3600 v2 Series

Reviews:

Related manuals for 3600 v2 Series

Brands by name

Popular brands