manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 93

 

86

 

Description 

Use 

bpdu-drop any

 to enable BPDU drop on a port. 

Use 

undo bpdu-drop any

 to disable BPDU drop on a port. 

By default, BPDU drop is disabled on a port. 

Examples 

# Enable BPDU drop on port Ethernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface ethernet 1/0/1 

[Sysname-Ethernet1/0/1] bpdu-drop any 

check region-configuration 

Syntax 

check region-configuration 

View 

MST region view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

check region-configuration

 to display MST region pre-configuration information, including the 

region name, revision level, and VLAN-to-instance mapping settings.  

Two or more spanning tree devices belong to the same MST region only if they are configured with 
the same format selector (0 by default, not configurable), MST region name, MST region revision 
level, and the same VLAN-to-instance mapping entries in the MST region, and if they are connected 
via a physical link. 

Hewlett Packard Enterprise recommends that you use this command to determine whether the MST 
region configurations to be activated are correct. Activate them only when they are correct. 

Related commands: 

instance

, 

region-name

, 

revision-level

, 

vlan-mapping modulo

, and 

active 

region-configuration

.  

Examples 

# Display MST region pre-configurations. 

<Sysname> system-view 

[Sysname] stp region-configuration 

[Sysname-mst-region] check region-configuration 

Admin Configuration 

   Format selector      :0 

   Region name          :000fe26a58ed 

   Revision level       :0 

   Configuration digest :0x41b5018aca57daa8dcfdba2984d99d06 

 

   Instance   Vlans Mapped 

      0       1 to 9, 11 to 4094 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands