HP 3100 v2 Series Command Reference Manual Download Page 69

Page: 69 / 239

Parameters

syslog

: Specifies that the device sends Syslog messages to inform the remote network

management device of MAC address changes.

trap

: Specifies that the device sends trap messages to inform the remote network management

device of MAC address changes.

Description

Use

mac-address information mode

to set the MAC Information mode (to use Syslog messages or

trap messages) to inform the remote network management device of MAC address changes.

Use

undo mac-address information mode

to restore the default.

By default, trap messages are sent to inform the remote network management device of MAC
address changes.

Examples

# Configure the device to send trap messages to inform the remote network management device of
MAC address changes.

<Sysname> system-view

[Sysname] mac-address information mode trap

mac-address information queue-length

Syntax

mac-address information queue-length value

undo mac-address information queue-length

View

System view

Default level

2: System level

Parameters

value

: Specifies the MAC Information queue length, in the range of 0 to 1000.

Description

Use

mac-address information queue-length

to set the MAC Information queue length.

Use

undo mac-address information queue-length

to restore the default.

By default, the MAC Information queue length is 50.

Examples

# Set the MAC Information queue length to 600.

<Sysname> system-view

[Sysname] mac-address information queue-length 600

Summary of Contents for 3100 v2 Series
















































































































































































































































Search results

Summary of Contents for 3100 v2 Series

Reviews:

Related manuals for 3100 v2 Series

Brands by name

Popular brands

HP 3100 v2 Series, Command Reference Manual

Search results

Summary of Contents for 3100 v2 Series

Reviews:

Related manuals for 3100 v2 Series

Brands by name

Popular brands