manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 67

 

60 

MAC Information configuration 
commands 

MAC Information applies only to Layer 2 Ethernet interfaces. 

mac-address information enable (interface view) 

Syntax 

mac-address information enable 

{

 added 

|

 deleted 

}

 

undo mac-address information enable 

{

 added 

|

 deleted 

} 

View 

Layer 2 Ethernet interface view 

Default level 

1: Monitor level 

Parameters 

added

: Enables the device to record security information when a new MAC address is learned on 

the Ethernet port.  

deleted

: Enables the device to record security information when an existing MAC address is deleted.  

Description 

Use 

mac-address information enable 

to enable MAC Information on the Layer 2 Ethernet 

interface. 

Use 

undo mac-address information enable 

to restore the default. 

By default, MAC Information is disabled on a Layer 2 Ethernet interface. 

This command is not supported on aggregate interfaces.  

To enable MAC Information on an Ethernet interface, enable MAC Information globally.  

Examples 

# Enable MAC Information on Ethernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface ethernet 1/0/1 

[Sysname-Ethernet1/0/1] mac-address information enable added 

mac-address information enable (system view) 

Syntax 

mac-address information enable 

undo mac-address information enable

 

View 

System view 

Default level 

2: System level 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands