manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 58

 

51 

If you execute this command using only the 

vlan

 keyword or the 

count

 keyword, or only these two 

keywords, it displays information of unicast MAC address entries and static multicast MAC address 
entries. 

Related commands: 

mac-address (system view)

,

 mac-address (interface view)

, and 

mac-address timer

; 

display mac-address multicast

 and 

display mac-address multicast count

 

(

IP Multicast Command Reference

). 

Examples 

# Display the MAC address table entry for MAC address 000f-e201-0101. 

<Sysname> display mac-address 000f-e201-0101 

MAC ADDR        VLAN ID    STATE            PORT INDEX       AGING TIME(s) 

000f-e201-0101  1          Learned          Ethernet1/0/1    AGING 

 

  ---  1 mac address(es) found  ---   

Table 11 Command output 

Field Description 

MAC ADDR 

MAC address. 

VLAN ID 

ID of the VLAN to which the MAC address belongs. 

STATE 

State of a MAC address entry: 

•

 

Config static

—The static entry manually configured by the user. 

•

 

Config dynamic

—The dynamic entry manually configured by the user.

•

 

Learned

—The entry learned by the device. 

•

 

Blackhole

—The blackhole entry. 

•

 

Multicast

—The static multicast MAC address entry manually 

configured by the user. For more information about static multicast 
MAC address entries, see 

IP Multicast Configuration Guide

. 

PORT INDEX 

Number of the port corresponding to the MAC address. Packets destined to 
this MAC address are sent out of this port. (Displayed as N/A for a blackhole 
MAC address entry). 

AGING TIME(s) 

Aging time: 

•

 

AGING

—The entry is aging. 

•

 

NOAGED

—The entry does not age.

 

1 mac address(es) found 

One MAC address entry is found. 

 

display mac-address aging-time 

Syntax 

display mac-address aging-time

 [ 

|

 { 

begin

 | 

exclude

 | 

include

 } 

regular-expression

 ] 

View 

Any view 

Default level 

1: Monitor level 

Parameters 

|

: Filters command output by specifying a regular expression. For more information about regular 

expressions, see 

Fundamentals Configuration Guide

. 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands