manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 46

 

39 

Loopback and null interface configuration 
commands 

default 

Syntax 

default 

View 

Loopback interface view, null interface view 

Default level 

2: System level 

Parameters 

None 

Description 

 

CAUTION: 

The 

default

 command might interrupt ongoing network services. Make sure you are fully aware of 

the impacts of this command when you use it on a live network. 

 

Use 

default

 to restore the default settings for the loopback or null interface. 

This command might fail to restore the default settings for some commands for reasons such as 
command dependencies and system restrictions. Use the 

display this

 command in interface view to 

identify these commands, and perform their 

undo

 forms or follow the command reference to restore 

their default settings. If your restoration attempt still fails, follow the error message to resolve the 
problem. 

Examples 

# Restore the default settings for interface loopback 0. 

<Sysname> system-view 

[Sysname] interface loopback 0 

[Sysname-loopback0] default 

This command will restore the default settings. Continue? [Y/N]:y 

description 

Syntax 

description

 

text

 

undo

 

description

 

View 

Loopback interface view, null interface view 

Default level 

2: System level 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands