HP 3100 v2 Series Command Reference Manual Download Page 33

Page: 33 / 239

<Sysname> system-view

[Sysname] loopback-detection enable

[Sysname] interface ethernet 1/0/1

[Sysname-Ethernet1/0/1] loopback-detection enable

loopback-detection interval-time

Syntax

loopback-detection interval-time time

undo loopback-detection interval-time

View

System view

Default level

2: System level

Parameters

time

: Sets the loopback detection interval, ranging from 5 to 300 seconds.

Description

Use

loopback-detection interval-time

to set the loopback detection interval.

Use

undo loopback-detection interval-time

to restore the default loopback detection interval.

The default loopback detection interval is 30 seconds.

Related commands:

display loopback-detection

Examples

# Set the loopback detection interval to 10 seconds.

<Sysname> system-view

[Sysname] loopback-detection interval-time 10

loopback-detection multi-port-mode enable

Syntax

loopback-detection multi-port-mode enable

undo loopback-detection multi-port-mode enable

View

System view

Default level

2: System level

Description

Use

loopback-detection multi-port-mode enable

to enable multi-port loopback detection.

Use

undo loopback-detection multi-port-mode enable

to restore the default.

By default, multi-port loopback detection is disabled.

If a device receives a packet that it sent out, a loop has occurred. Depending on whether the
receiving interface is the same as the sending interface, loops include the following categories:

Summary of Contents for 3100 v2 Series
















































































































































































































































Search results

Summary of Contents for 3100 v2 Series

Reviews:

Brands by name

Popular brands

HP 3100 v2 Series, Command Reference Manual

Search results

Summary of Contents for 3100 v2 Series

Reviews:

Brands by name

Popular brands