manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 211

 

204 

[Sysname] interface ethernet 1/0/1 

[Sysname-Ethernet1/0/1] lldp compliance admin-status cdp txrx 

lldp compliance cdp (available only on the HPE 3100 v2 EI) 

Syntax 

lldp compliance cdp 

undo lldp compliance cdp

 

View 

System view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

lldp compliance cdp

 to enable global CDP compatibility.  

Use 

undo lldp compliance cdp

 to restore the default.  

By default, CDP compatibility is globally disabled.  

The maximum TTL allowed by CDP is 255 seconds. To make CDP-compatible LLDP work correctly 
with Cisco IP phones, the TTL configuration must be no more than 255 seconds. The TTL 
configuration is the product of the TTL multiplier and the LLDP frame transmission interval. 

Related commands: 

lldp hold-multiplier

 and 

lldp timer tx-interval

.  

Examples 

# Enable LLDP to be compatible with CDP globally.  

<Sysname> system-view 

[Sysname] lldp compliance cdp 

lldp enable 

Syntax 

lldp enable 

undo lldp enable

 

View 

System view, Layer 2 Ethernet interface view, port group view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

lldp enable

 to enable LLDP. 

Use 

undo lldp enable

 to disable LLDP. 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands