manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 185

 

178 

<Sysname> system-view 

[Sysname] interface ethernet 1/0/1 

[Sysname-Ethernet1/0/1] garp timer leave 100 

garp timer leaveall 

Syntax 

garp timer leaveall timer-value 

undo garp timer leaveall 

View 

System view 

Default level 

2: System level 

Parameters 

timer-value

: Leaveall timer (in centiseconds), which must be a multiple of 5 and range from the 

maximum Leave timer on the device (exclusive) to 32765 (inclusive). 

Description 

Use 

garp timer leaveall

 to set the GARP LeaveAll timer.  

Use 

undo garp timer leaveall

 to restore the default. This may fail if the default is beyond the valid 

value range for the LeaveAll timer.  

By default, the LeaveAll timer is 1000 centiseconds.  

 

 

NOTE: 

To keep the dynamic VLANs learned through GVRP stable, do not set the LeaveAll timer smaller 
than its default value.  

 

Related commands: 

display garp timer

 and 

garp timer leave

. 

Examples  

# Set the leaveall timer to 2000 centiseconds, assuming that the Leave timer on every port is set to 
60 centiseconds.  

<Sysname> system-view 

[Sysname] garp timer leaveall 2000 

gvrp 

Syntax 

gvrp 

undo gvrp 

View 

System view, Ethernet interface view, Layer-2 aggregate interface view, port group view 

Default level 

2: System level 

Parameters 

None 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands