manualshive.com logo in svg

HP 268 Pro G1 MT, Maintenance And Service Manual

Share
Download
HP 268 Pro G1 MT Maintenance And Service Manual Download Page 44

System board callouts

Table 4-6

  System board callouts

Item

Color

Component

 

Item

Color

Component

1

White

Power supply P1 
connector

 

6

Black

Power button board 
connector

2

White

Power supply P2 
connector

 

7

White

Power supply P3 
connector

3

Black

Drive power connector

 

8

Black

Processor fan

4

Black

Drive data connectors

 

9

Black

System fan

5

Black

M.2 solid-state drive 
connector

 

 

 

 

Changing from desktop to tower configuration

The computer can be used in a tower orientation with an optional tower stand that can be purchased from HP.

Before changing computer configuration, follow these steps:

▲

Prepare the computer for disassembly (

Preparation for disassembly on page 16

).

Change computer configuration:

1.

Orient the computer so that its right side is facing up and place the computer in the optional stand.

NOTE:

To stabilize the computer in a tower orientation, HP recommends the use of the optional tower 

stand.

2.

Reconnect the power cord and any external devices, then turn on the computer.

NOTE:

Ensure at least 10.2 centimeters (4 inches) of space on all sides of the computer remains clear and 

free of obstructions.

3.

Lock any security devices that were disengaged when the access panel was removed.

36

Chapter 4   Removal and replacement procedures

Summary of Contents for 268 Pro G1 MT











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands