FOR YOUR SAFETY, PLEASE FOLLOW THESE PRECAUTIONS:
!
ALWAYS REMOVE THE TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT.
!
BE CAREFUL WHEN MOVING THE ASSEMBLED FURNITURE AFTER THE GLASS SHELF HAS BEEN INSTALLED,
AND/OR WHEN THERE IS EQUIPMENT LOCATED ON THE FURNITURE AS THIS MAY CAUSE THE SHELF TO BECOME
UNSECURED AND FALL.
!
WHEN IN USE, THIS FURNITURE MUST BE PLACED ON A FLAT, SOLID AND LEVEL SURFACE.
!
DO NOT LEAN ON THE TV WHEN IT IS ON THE TV STAND.
!
DO NOT CLIMB OR STEP ON THE STAND.
!
DO NOT BANG OR PLACE YOUR OWN WEIGHT ON THE GLASS SHELF.
!
DO NOT PLACE ITEMS ON THE SHELVES WHICH EXCEED THE MAXIMUM WEIGHT LIMITS OF 200 LBS. FOR TOP SHELF
AND 50 LBS. FOR GLASS SHELF
Assembly Instructions
Parts List
A.
INSERT
two Cam Locks (8) into each of the Side Support
Panels (9) as shown in Fig. 1.
INSERT
two additional Cam
Locks into each of the the Left and Right Front Panels (3).
B.
INSERT
2 Cam Lock Connector Bolts (6) into each of the
Left and Right Front Panels (3) as shown.
C.
ATTACH
each Front Panel (3) to each Side Support Panel
(9) as shown in Fig. 1.
TIGHTEN
cam locks (8) 1/4 turn with
a philips screwdriver, DO NOT OVERTIGHTEN.
Fig. 1
3
8
8
1. Side Assembly
9
6
11
2. Table Assembly
A.
PLACE
the Bottom Shelf (1) on a soft flat surface with the square feet facing
down.
INSERT
four Cam Lock Connector Bolts (6) and insert four Wood Dowels (7) as shown in Fig. 2.
B.
INSERT
four Cam Locks (8) into the back of the Rear Support Panel (2).
PLACE
the Rear Support Panel over the Cam Lock
Connector Bolts (6) and Wood Dowels (7) located in the rear of the Bottom Shelf (1) as shown in Fig. 2 and
LOCK
the Rear
Support Panel in place by turning the Cam Locks. TIP the Bottom Shelf (1) on edge so that the underside is facing you.
INSERT
three 50 mm Screws (10) through the bottom of the shelf and into the bottom of the Rear Support Panel and tighten
to
SECURE
.
C. CAREFULLY TIP the Bottom Shelf/Rear Support Panel assembly into an upright position.
ATTACH
the Side/Front Panel
assemblies to the Bottom Shelf (1) as shown in Fig. 2 and
SECURE
by turning the Cam Locks (8) located in the Side Panels (9).
D. CAREFULLY TIP the partially assembled table onto its back and
INSERT
two 50 mm Screws (10) from the underside of the
Bottom Shelf (1) into the bottoms of the Side/Front Panel assemblies. Tighten to
SECURE
.
E. CAREFULLY TIP the table upright again.
INSERT
two Glass Shelf Support Pins (11) into the front of the Rear Support Panel (2).
INSERT
one Glass Shelf Support Pins into the predrilled holes in each Side Support Panel (9), and one Glass Shelf Support Pin
into each of the Front Panels (3) as shown in Fig. 1. Make sure the rubber pads on the Support Pins are facing up.
F. CAREFULLY PLACE the Glass Shelf (4) into the partially assembled table so that it is resting on the Glass Shelf Support Pins (11).
G.
INSERT
one Wood Dowel (7) into the top of each Front Panel (3) and two Dowels
into the top of the Rear Support Panel (2).
INSERT
four Cam Lock
Connector Bolts (6) into the prethreaded holes in the underside of
the Top Shelf (5).
PLACE
the Top Shelf onto the Rear Support
Panel and Side Panels assembly as shown in Fig. 2, and
SECURE
the Top Shelf by turning the
Cam Locks.
INSERT
seven
Screws (10) through the Top
Shelf and into the tops of the
Rear Support Panel and
Side Panels and tighten to
SECURE
.
NOTE: For your safety,
SECURE the TV to the table
from beneath the the top shelf
using 4 of the supplied 30mm bolts (PART #12).
NOTE: THE GLASS SHELF (4) CANNOT BE REMOVED ONCE
THE TOP SHELF (5) IS SECURED, BUT IT CAN SHIFT OR TIP
FORWARD IF THE TABLE IS MOVED OR IF THE SHELF
SUPPORT PINS (11) ARE NOT PLACED SECURELY IN THEIR HOLES WITH THE
RUBBER PADS FACING UP. ALWAYS PLACE HEAVIEST COMPONENTS ON THE BOTTOM SHELF.
Fig. 2
10
10
6
2
4
5
9
9
1
3
3
8
6
6
6
8
11
11
6
7
7
7
7
7
NOTE:
TWO PEOPLE ARE RECOMMENDED TO ASSEMBLE THIS TABLE.
34mm Cam Lock Connector Bolt
50mm Screw
30mm Screw
Wood Dowel
Cam Lock
Glass Shelf Support Pins
Left & Right Front Panels
Side Support Panels
Rear Support Panel
with Cable Management
Top Shelf
Glass Shelf
Bottom Shelf
PART #
QUANTITY
PART DESCRIPTION
6
REQUIRED
TOOLS
14
4
8
12
12
6
2
2
1
1
1
1
10
12
7
8
5
4
1
11
3
9
2
Allen Wrench
Philips Screwdriver
