background image

12

Operations

Operating Instructions

Hotsy HWE Operator’s Manual  8.941-225.0 - Y

STEP 1:

 Connect the high pressure 

hose quick coupler to the discharge 
nipple by sliding the quick coupler 
collar back and inserting the quick 
coupler onto the discharge nipple 
and pushing the quick coupler 
collar forward to secure it. Secure 
desired pressure nozzle into 
variable pressure wand coupler.

STEP 2:

 Connect water supply 

hose (garden hose) to inlet 
connector. Do not allow acid or 
abrasives to be pumped through 
system. Turn on water.

S

TEP 

3

:

 Place toggle switch in the 

ON position and then pull the 
trigger on the spray gun to activate 
a pressure switch which will then 
start the machine. The ON position 
is for auto shut down.

STEP 4:

 Turn the variable pressure control handle clockwise to increase 

pressure.

NOTE: Selection of high or low pressure is accompanied by turning the 
handle. High pressure nozzle must be inserted at end of wand to obtain 
high pressure. To apply soap read Detergents & General Cleaning 
Techniques section.

STEP 5:

 To stop machine, release 

the spray gun and machine will 
automatically stop in approximately 
12 seconds. If machine is going to 
be unattended for long periods of 
time, turn water supply off and place 
switch in OFF position.

NOTE: When removing or 
replacing hoses, wand and 
nozzles, move switch to OFF 
position, open spray gun to 
release pressure before removing 
discharge hose.

Variable Pressure 

Control Handle

Trigger

Variable Pressure 

Wand (VP)

High 

Pressure 

Nozzle

Brass Soap 

Nozzle

PRECAUTION

ATTENTI

ON

INSTRUCC

ION

ES

High Pressure 

Hose Coupler

Discharge 

Nipple

COLD

WA

TER

INLET

COLD

WA

TER

OUTLET

40°

40°

25°

WA

R

15°

ON

PRENDER

OFF

I

O

Inlet

Garden 

Hose

COLD

WA

TER

INLET

COLD

WA

TER

OUTLET

INSTRUCTIONS

40°

40°

25°

WARNING

PRECAUTION

ATTENTION

INS

TRU

INSTRUCCIONES

15°

ON

PREND

ER

OFF

I

O

EXPOSED PULLEYS AND
BEL

TS CAN CAUSE

INJUR

Y

PRECAUCION/A

VER

TISSEMENT

W

ARNING

Toggle 
Switch

COLD

WA

TER

INLET

COLD

WA

TER

OUTLET

INSTRUCTIONS

40°

40°

25°

WARNING

PRECAUTION

ATTENTION

INS

TRU

INSTRUCCIONES

15°

ON

PRENDER

OFF

I

O

EXPOSED PULLEYS AND
BEL

TS CAN CAUSE

INJUR

Y

PRECAUCION/A

VER

TISSEMENT

W

ARNING

Summary of Contents for HWE-4020C





















































Reviews: