Hotsy 680SS Operating Instructions And Parts Manual Download Page 22

Page: 22 / 28

HOTSY 680SS • 8.914-368.0 • Rev. 02/15

PRESSURE WASHER

OPERATOR’S MANUAL

COIL OUTLET ASSEMBLY EXPLODED VIEW & PARTS LIST

HOSE, GUN & WAND ASSEMBLY AND PARTS LIST

ITEM PART NO.

DESCRIPTION

QTY

9-149-003.0 Manifold Coil Outlet Discharge 1

8.706-241.0

Plug, 3/8" Sq Head Galv

9.196-012.0

Screw, 10-24 x 1/4" Hex Set

9.802-041.0

Elbow, 3/8" Street 45 Deg Steel 1

9.802-171.0

Coupler, 3/8" Plug, Male,

Steel/Zinc

8.902-433.0 Valve, Safety Relief Vsa

8.711-785.0

Hose, 3/8" Push On, Per Ft 33.5"

9.800-021.0

Label, Hot Water Outlet

ITEM PART NO.

DESCRIPTION

QTY

8.712-406.0

Nozzle, Variable Fan, 1/4"

F#6

8.725-389.0 Wand, Single, 36", Insulated

W/ Side Grip

9.802-164.0

Coupler, 1/4" Socket, Female, 1

Brass

8.707-139.0

Coupler, 1/4"Plug, Male,

Steel/Zinc

8.751-235.0

Gun, Hotsy, H1050, 5000 PSI, 1

10.4

Gpm

8.739-011.0

Hose, 3/8" x 50', 1W, Ts, Hotsy 1

So x Sw

REPLACEMENT PARTS

8.717-661.0

Grip, Handle Assy Hotsy

8.706-670.0 Grip, Wand Side Handle

8.751-119.0

Kit, Gun Repair

Summary of Contents for 680SS





























Search results

Summary of Contents for 680SS

Reviews:

Related manuals for 680SS

Brands by name

Popular brands

Hotsy 680SS, Operating Instructions And Parts Manual

Search results

Summary of Contents for 680SS

Reviews:

Related manuals for 680SS

Brands by name

Popular brands