background image

34

1

Freeze-Up Check List

Please Complete When Diagnosing a Freeze-Up, Refrigerant Leak, or Low Charge

Technical Support Fax #: 770-487-3360

Make Copies And Use As Needed

Model #___________________________ Serial # _________________________Install Date______________Fail Date___________

List model and manufacture of bin or dispenser__________________________.
Date appliance was last cleaned:__________.

Freeze-Up Defrost

YES   NO
[   ] 

[   ] 

1) After defrosting, was the appliance leak 

checked?

[   ] 

[   ] 

2) Were any leaks found? 

If so where?_____________________. 

[   ] 

[   ] 

3) Was any refrigerant added to the unit? 

If so, how much?_________________.

Set Up

[   ] 

[   ] 

4) Is the appliance stacked?

[   ] 

[   ] 

5) Is water line independent?  

[   ] 

[   ] 

6) Is water line correct size? If not________”. 

3/8" Nominal ID Copper Water Tubing or 
Equivalent.

 7) What is water pressure?___________. 

Water Temperature_________.

[   ] 

[   ] 

8) Does appliance have any water filtration?  

If yes please list the following:        
Filter brand___________________.
Model________________. 
Filter pressure gauge reading during the fill 
cycle___________. 
Date filter was last 
replaced?__________________________. 
GPM or LPM flow rate of filter 
system?__________________.

   9) Ambient temperature at appliance? 

______________.

    At remote condenser (if applicable)?________.

Appliance Status

[   ] 

[   ]     10) Is the appliance and/or float switch dirty?

11) List the S4 (1-10) and S5 (1-5) DIP switch 

settings. 

S4: 1___2___3___4___5___6___7___8___9___10____ 
S5: 1_____2_____3_____4_____5______
[   ] 

[   ]     12) Is DIP switch number 7 ON (harvest pump      

time (harvest assist) all models and freeze-time 
correction models with control board  
2A7664-02?

[   ] 

[   ]     13) Is the cube guide positioned correctly?

[   ] 

[   ]     14) Are the evaporator separators positioned 

properly?

[   ] 

[   ]     15) Is the thermistor properly mounted, tight, and 

insulated? 

[   ] 

[   ]     16) Is the TXV bulb properly mounted, tight, and 

insulated?

Appliance Operation

 

 

 

    

Fill

YES   NO
[   ] 

[   ]     17) Does the water tank fill and overflow?  

60-90 sec. Note: Larger models may take up to 
120 seconds to overflow when empty.

[   ] 

[   ]     18) If NO in step 17, is water flow 5GPM for larger? 

[   ] 

[   ]     19) Does the appliance utilize re-fill (S5 dip switch 

2 and 3)?

 

 

    

Harvest

[   ] 

[   ]     20) Is the hot gas valve opening?

[   ] 

[   ]     21) Is harvest pump time (harvest assist) utilized 

(S4dip switch 7)?

[   ] 

[   ]     22) Is hot gas valve opening in harvest?

[   ] 

[   ]     23) Does water valve close completely when  

de energized?

24) What was length of harvest?___________.

 

 

    

Freeze

[   ] 

[   ]     25) Is pump motor energized in freeze cycle except 

during 10-sec. anti-slush. If activated (S5 dip 
switch 5 on)?

26) Water-cooled condenser outlet temperature 

5-min. into freeze?  ______________°F. 

27) What was length of freeze?____________.

[   ] 

[   ]     28) Is the cube size consistent from inlet to outlet of 

evaporator?

[   ] 

[   ]     29) Is ice still dropping when next freeze cycle starts?

30) What is the ice drop weight?___________.
31) What is head pressure?  

Freeze_________Harvest_______.  
(Freeze pressure should be taken 5 minutes into 
the cycle). 

32) What is suction pressure?  

Freeze______Harvest_______.  
(Freeze pressure should be taken 5 minutes into 
the cycle). 

[   ] 

[   ]     33) When activating bin control, did appliance 

shutdown within 15 seconds in the first 5 minutes 
of freeze cycle?

Freeze-Time Correction Operation

[   ] 

[   ]     34) Has Freeze-Time Correction been activated? 

("POWER OK" LED blinking).

[   ] 

[   ]     35) Has more than 1 Freeze-Time Correction been 

activated?  
(POWER OK" LED and "EXT HARVEST" LED 
blinking). 

Note: Make copies of this form and use it when diagnosing a freeze up condition. Submit a completed copy of the checklist 

along with the freeze-up labor claim form.

J. Freeze-Up Check List

Summary of Contents for KMS-1122MLJ


























































Reviews: