HORNER XL6 Series Installation Manual Download

Page: 3 / 6

MAN0886-03-EN

Specifications / Installation

__________________________________________________________________________________________________________________________________________________________________

4/28/2009 Page 3 of 6 ECN # 950

Ports and Connectors

To Remove I/O Cover:

Unscrew 4 screws located on the

cover.

Remove cover.

CAUTION: Do not over tighten

screws when replacing the back

cover.

I/O Jumpers:

I/O Jumpers (JP) are located internally.

To access, remove I/O cover of unit.

Wiring Connectors (J1 / J2 / J3 / J4)

and I/O Jumpers (JP1 and JP3) are

described in the Wiring and Jumpers

section of this document.

Memory Slot:

Uses Removable Memory for data

logging, screen captures, program

loading and recipes.

Horner Part No.: HE-MC1

Serial Communications:

MJ1: (RS-232 / RS-485) Used for

Cscape programming and Application-

Defined Communications.

MJ2: (RS-232 / RS-485) Used for

Application-Defined Communications.

Ethernet: Used for Cscape

programming and Application-Defined

Communications.

Summary of Contents for XL6 Series







Search results

Summary of Contents for XL6 Series

Reviews:

Related manuals for XL6 Series

Brands by name

Popular brands

HORNER XL6 Series, Installation Manual

Search results

Summary of Contents for XL6 Series

Reviews:

Related manuals for XL6 Series

Brands by name

Popular brands