HORNER EXLW PRIME Series User Manual Download

Page: 41 / 201

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

41 | 201

5.11 Set Screen

The Set Screen Sub-Menu displays four System Settings, all of which may be edited.

Saver Enable

Yes = Enable screen saver

(default)

= Disable screen saver

Timeout (min)

5 - 1200 = Amount of time in minutes to expire with NO touch
activity before activating screen saver (black screen)

Popup Status

Off

(default)

= Disable popup status

Warning = Display popup status only if controller status changes
to NOT Ok or NOT Run mode.
On = Display popup status on any controller status change.

Update Time (mS)

2 - 50 = Maximum amount of time to allow for graphics update
per scan

Summary of Contents for EXLW PRIME Series










































































































































































































Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands

HORNER EXLW PRIME Series, User Manual

Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands