HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 18 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

18 | 201

Once the panel design has been completed using the criteria and suggestions in the following
sections, use the following steps to panel mount the EXLW/XLW PRIME OCS.

1.

Remove all connectors from the EXLW/XLW PRIME OCS unit.

2.

Make sure the gasket is installed on the EXLW/XLW PRIME OCS and is free from dust
and debris. Check that the corners of the gasket are secure.

3.

Pass the unit through the panel.

4.

Insert each of the ten (10) mounting clips into the slots in the EXLW/XLW PRIME OCS
case. One clip should be installed on each corner. Lightly tighten each screw so the clip
is held in place.

5.

Tighten the screws on the clips such that the gasket is compressed against the panel.
Recommended torque is 4-8 in-lbs (0.45-0.90 N-m).

3.3 Mounting Orientation

3.3.1 EXLW/XLW PRIME OCS Mounting Clip

Figure 3.2

–

EXLW/XLW PRIME OCS with Mounting Clips

001XLQX007

«
...
16
17
18
19
20
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Jafar Pages: 9

Brand: Raymarine Pages: 12

Brand: Jafar Pages: 13

Brand: FrSky Pages: 2

ecomat 100 R 360

Brand: IFM Electronic Pages: 16

Ecomot300 AC2630

Brand: IFM Electronic Pages: 11

Brand: IFM Electronic Pages: 23

Brand: Jäger Pages: 50

Brand: Union Instruments Pages: 63

Brand: ZIMMERLI MESSTECHNIK Pages: 12

EP Series Pro-Bloc

Brand: Parker Pages: 11

Brand: Parker Pages: 22

Brand: Parker Pages: 2

Brand: YASKAWA Pages: 340

Lux Intelligent

Brand: Advanced Pages: 62

Brand: intech 21 Pages: 15

Brand: Xsens Pages: 17

Brand: Samcen Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands