HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 163 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

163 | 201

CHAPTER 18: FAIL

–

SAFE SYSTEM

18.1 Overview

The Fail-Safe System is a set of features that allow an application to continue running in the
event of certain types of "soft" failures. These "soft" failures include:

-

Battery power loss

-

Battery-Backed Register RAM or Application Flash corruption due to an excessive EMI,
Electromagnetic Interference, event, for example.

The Fail-Safe System has the following capabilities:

-

Manually backup the current Battery-Backed RAM Register Settings into Flash
memory.

-

Manually restore Register Settings from the values previously backed up in Flash to
Battery-Backed RAM.

-

Detect corrupted Register Settings at power-up and then automatically restore
them from Flash.

-

Detect corrupted or empty application in Flash memory at power-up and then
automatically load the AUTOLOAD.PGM application file from Removable Media
(Compact Flash or microSD).

-

If an automatic Register Restore or Application Load occurs, the OCS can
automatically be placed in RUN mode.

The fail-safe system can be accessed by going to the System Menu of the controller. A new

menu “Fail

-

Safe System” has been added at the end of the main

System Menu for this. Selecting

“Fail

-

Safe System” menu will open the following menu screen:

Figure 18.1

–

Fail

–

Safe System Menu

«
...
161
162
163
164
165
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Harmonic Drive Pages: 25

Brand: Nelson Pages: 8

Brand: Samson Pages: 73

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: Rane Pages: 2

Brand: UNICORECOMM Pages: 32

Brand: UNICORECOMM Pages: 7

Brand: UNICORECOMM Pages: 26

Brand: UNICORECOMM Pages: 25

Brand: Parker Pages: 4

Brand: Full Gauge Controls Pages: 3

Brand: V2 Pages: 48

Brand: Data Signs Pages: 23

Brand: nvent Pages: 6

Brand: Smart Vision Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands