Horizon Fitness OXFORD 3 ROWER Service Manual Download | Manualshive

Page: 24 / 29

background image

24

CHAPTER 6:PARTS REPLACEMENT

6.7 CONTROLLER BOARD

（

OXFORD 6 ONLY

）

1. Disconnect the wire, remove the knob screws (004621-00) and remove the knob (1000414889).

2. Remove the knob cover (1000412398), lamp stand (1000412397) and butt plate (1000414975).

3. Remove the nut and pull out the board (1000412436).

«
...
22
23
24
25
26
...
»

Summary of Contents for OXFORD 3 ROWER






























Reviews:

No comments

Related manuals for OXFORD 3 ROWER

Brand: MAHLE Pages: 21

Brand: PANDROL Pages: 36

Life/form SmartScope LF01142U

Brand: Nasco Pages: 2

Brand: PASCO Pages: 5

Brand: Pasco Scientific Pages: 27

Brand: PARUS Pages: 6

Brand: quadient Pages: 14

Brand: Qu-Bit Electronix Pages: 31

Brand: Yamaha Pages: 29

Brand: Össur Pages: 98

Flex Foot Cheetah

Brand: Össur Pages: 107

Brand: Össur Pages: 38

Brand: Össur Pages: 39

Bionic Symbionic Leg

Brand: Össur Pages: 2

Brand: Össur Pages: 67

Brand: Össur Pages: 17

Brand: Össur Pages: 82

Brand: EuroLite Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands