Horizon Fitness OXFORD 3 ROWER Service Manual Download | Manualshive

Page: 20 / 29

background image

20

CHAPTER 6:PARTS REPLACEMENT

6.4 CONSOLE & CONSOLE WIRE

1. Remove the console mast cover (1000409269), console cover screws (004623-00), link screw

(004488-AC) and nut (004926-00).

2. Remove wire connection carefully.

3. Remove side cover (section 6.1) and loosen front cover screws (004621-00) on both sides.

Note:

There is only one speed sensor wire connected with OXFORD 3 console board.

«
...
18
19
20
21
22
...
»

Summary of Contents for OXFORD 3 ROWER






























Reviews:

No comments

Related manuals for OXFORD 3 ROWER

Brand: MacDon Pages: 84

Brand: MacDon Pages: 89

Brand: Patton electronics Pages: 18

WJHD309 - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 7

WJ-ND300 Administrator Console

Brand: Panasonic Pages: 24

Brand: JB Systems Pages: 7

Brand: 3B SCIENTIFIC PHYSICS Pages: 36

Brand: 3A HEALTH CARE Pages: 16

Short/cut 2000 Audio Editor

Brand: 360 Systems Pages: 4

Brand: FEAS Pages: 72

Brand: J.P. SELECTA Pages: 32

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Zimmer Pages: 54

Brand: Zimmer Pages: 4

Brand: Zimmer Biomet Pages: 23

Brand: Zimmer Pages: 16

Brand: Zimmer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands