hopf 8029HEPTA-V2/GPS Technical Manual Download Page 94

Page: 94 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

94 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.5.11 Downloading Configuration Files / SNMP MIB

In order to be able to download certain configuration files via the web interface, it is necessary
to be logged on as a

"master"

user.

The loaded file

System Configuration

from the module is only used for

support purposes and cannot be reloaded for adjusting the settings in the
Time Server 8029HEPTA/GPS.

For the download of the file

System Configuration

the following process

is mandatory:

1. Pressing the button

SAVE

2. Pressing the button

Refresh System Configuration

3. After approximately 30 seconds, the files are available for the

download

4. Press on the link Configuration Files to update the web site
5. Perform the download of the file

The "private

hopf

enterprise MIB" is also available via the WebGUI in this area.

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands