hopf 8029HEPTA-V2/GPS Technical Manual Download Page 9 | Manualshive

Page: 9 / 130

background image

GPS

-

NTP

T

IME

S

ERVER

8029HEPTA/GPS

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

9 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

1

GPS - NTP Time Server 8029HEPTA/GPS

By GPS time synchronization and the worldwide used time protocol

NTP (Network Time

Protocol)

the Time Server 8029HEPTA/GPS turns into a highly accurate

NTP Stratum 1

Time

Server. It is used for the synchronization of computers and industrial networks.

The Time Server supports the following synchronization protocols:

•

NTP (incl. SNTP)

•

Daytime

•

Time

•

SINEC H1 time datagram (

Activation Key necessary

)

Front Side

Rear Side

The Time Server 8029HEPTA/GPS is integrated into a 1U/84HP 19" rack and characterized
by its easy and simple operation. Some of these practice-oriented functionalities are e.g.:

•

Complete parameterisation via protected WebGUI access

All required settings for operation can be executed via a password protected WebGUI
also giving an overview of the status of the Time Server 8029HEPTA/GPS.

•

LCD-Display and Status-LEDs in the front panel

The LCD-Display and the Status-LEDs make rapidly and easily substantial information
for commissioning, on the operating status and for support matters available if a
problem occurs, even without WebGUI access.

•

Monitoring of GPS antenna circuit

An error message is generated when there is a short circuit in the GPS antenna circuit
or an open antenna input.

•

Automatic switch-over of summer/winter time

(initial setting required)

After initial commissioning there is no user intervention for a correct summer/winter
time changeover for the following years required.

•

Automatic handling of the leap second

Should a leap second be inserted in the UTC time, it is recognized by the Time Server
8029HEPTA/GPS via the GPS signal and the leap second is automatically inserted in
the time information.

•

Customized extensions possible

The new designed housing concept allows customized system extensions for
additional signal outputs (processed ex-works) easily and fast.

«
...
7
8
9
10
11
...
»

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments

Related manuals for 8029HEPTA-V2/GPS

Brand: Happijack Pages: 2

Brand: Siemens Pages: 172

Brand: Siemens Pages: 241

Brand: MINOURA Pages: 1

Brand: Braillo Pages: 127

Brand: Avanti Pages: 20

Brand: BECKWITH ELECTRIC Pages: 53

Brand: EHEIM Pages: 112

Brand: Alpine Pages: 6

Brand: Aqua One Pages: 16

Professional Foam Lance 14.0263

Brand: MTM HYDRO Pages: 2

Brand: Backfire Pages: 20

Brand: Sagem Pages: 284

Brand: Unika Pages: 12

Brand: iCarsoft Pages: 2

MC9000ex Series

Brand: Bartec Pages: 9

Brand: kincrome Pages: 7

Brand: kincrome Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands