hopf 8029HEPTA-V2/GPS Technical Manual Download Page 67 | Manualshive

Page: 67 / 130

hopf 8029HEPTA-V2/GPS Technical Manual Download Page 67

HTTP/HTTPS

W

EB

GUI

–

W

EB

B

ROWSER

C

ONFIGURATION

I

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

67 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.3.2 Kernel Info

The “Kernel Info” overview shows the current error values of the internal embedded Linux
clock. Both values are internally updated every second.

This screenshot shows a maximum kernel clock error of 4.500 msec (milliseconds). The
estimated error value is 5

μs (microseconds).

The values indicated here are based on the calculation of the NTP service and have no
significance for the accuracy of the Sync Source (here Module 8024GPS).

8.3.3.3 Peers

The “Peers summary” is used to track the performance of the configured NTP server/driver
and the NTP algorithm itself.

The information displayed is identical with the information available via NTPQ or NTPDC
programs.

Each NTP server/driver that has been set up in the NTP server configuration is displayed in
the peer information.

The connection status is displayed in the reachability column (not reachable, bad, medium,
and reachable).

The first line displays the

hopf

- refclock ntp driver

that gets the time information directly

from the Sync Source.

A short explanation and definition of the displayed values can be found in

Chapter

Accuracy & NTP Basic Principles

The character in the first column on the left presents the current status of the NTP association
in the NTP selection algorithm. A list and description of possible characters can be found in
the Glossary (see

Chapter 14.2 Tally Codes (NTP-specific)

«
...
65
66
67
68
69
...
»

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments