manualshive.com logo in svg

hopf 8029HEPTA-V2/GPS, Technical Manual, Page: 18 / 130

Share
Download
hopf 8029HEPTA-V2/GPS Technical Manual Download Page 18

 

F

UNCTION 

P

RINCIPLE

 

 

 

 8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00 

18 / 130 

hopf 

Elektronik GmbH   

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

3  

Function Principle 

This  chapter  describes  the  function  principle  of  the  Time  Server  8029HEPTA/GPS  and  the 
internal relations between the different functional groups.  

3.1  

Block Diagram 

 

 

•

 

Firmware Update 

A  H8  firmware  update  of  the  Sync  Source  (here  Module  8024GPS)  is  completely 
controlled by Module 8029HEPTA. 

The  update  file  for  Module  8024GPS  is  loaded  into  Module  8029HEPTA  via  LAN 
through  the  WebGUI.  Then  Module  8029HEPTA  performs  the  update  of  the  Sync 
Source (here Module 8024GPS) independently. 

 

 

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments