Honsel Rivdom eVNG2 Operation Manual Download

Page: 32 / 32

Operation Manual

Edition: May 2021

Version 1

English

Failure Diagnostic

Disorder

Possible Cause

Troubleshooting

No battery inserted

Insert battery

battery empty

Charge the battery

The device is locked

Unlock the device in the expert menu / tool lock

Standby time of the LED foot light set to Change the time setting in the general menu

Foot LED defective

Send the device to the HONSEL repair service

Force set too high or too low

Set up the blind rivet nut or screw again

Stroke set too high or too low

Spindle time too short

Set up the blind rivet nut or screw again

Unwinding time too short

Extend the unwinding time in the expert menu / spindle setting

Device switched off / battery empty

Set device / change battery

Unscrewing mode set incorrectly

Threaded mandrel / sleeve were blocked

Check in the expert menu / unscrewing mode

Release the handle once without a blind rivet nut / screw

Defective pusher

Send the device to the HONSEL repair service
Remove the battery and reinsert it after 2 seconds

Software malfunction

Make software update

Remove the battery and reinsert it after 2 seconds

Software malfunction

Make software update

The service is due - note the ad

Send the device to the HONSEL repair service for maintenance

A warning has been received

Read the warning message on the OLED and act accordingly
see chapter 10

Device is in emergency mode

Read the warning message on the OLED and act accordingly
see chapter 10

After switching on, the device does not

make a proper calibration run

The protruding threaded mandrel / screw

length is changing

After switching on you have to wait

before you can work with the riveting tool

RGB LED lights up red continuously

RGB LED flashes red

Riveting tool does not respond

LED foot light does not light up or goes out

again immediately

Blind rivet nut or screw is not set correctly

Blind rivet nut or screw is not screwed on

correctly

Blind rivet nut or screw is not spindled off

correctly

The trigger or threaded mandrel / sleeve

do not trigger the spindle

Summary of Contents for Rivdom eVNG2

































Search results

Summary of Contents for Rivdom eVNG2

Reviews:

Related manuals for Rivdom eVNG2

Brands by name

Popular brands

Honsel Rivdom eVNG2, Operation Manual

Search results

Summary of Contents for Rivdom eVNG2

Reviews:

Related manuals for Rivdom eVNG2

Brands by name

Popular brands