Honeywell VX3Plus Reference Manual Download Page 278

Page: 278 / 282

Environmental Specifications

Operating Temperature

14°F to 122°F (-10°C to 50°C) [non-condensing]

Storage Temperature

-22°F to 158°F (-30°C to 70°C) [non-condensing]

ESD

8 KV air, 4kV direct contact

Operating Humidity

5% to 95% non-condensing at 104°F (40°C)

Water and Dust

IEC 60529 compliant to IP66

ESD

15 kV

Vibration

Based on MIL Std 810D

Altitude

Operational to 10,000 ft. (3048 meters)

Network Card Specifications

Summit 802.11 b/g CF 2.4GHz

Bus Interface

16-bit CompactFlash Type I with 50-pin connector

Wireless Frequencies

2.4 to 2.4897 GHz

RF Data Rates

1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps

RF Power Level

50 mW max.

Channels

1-11 FCC, 1-13 ETSI

Operating Temperature

Same as VX3Plus Operating Temperature

Storage Temperature

Same as VX3Plus Storage Temperature

Connectivity

TCP/IP, Ethernet, ODI

Diversity

Yes

7-2

Summary of Contents for VX3Plus



























































































































































































































































































Search results

Summary of Contents for VX3Plus

Reviews:

Honeywell VX3Plus, Reference Manual, Page: 278 / 282

Search results

Summary of Contents for VX3Plus

Reviews: