manualshive.com logo in svg

Honeywell VX3Plus, Reference Manual, Page: 202 / 282

Share
Download
Honeywell VX3Plus Reference Manual Download Page 202

Data

The Data tab controls when data is transferred between the VX3Plus and the Mobile Device Server.

Network

When checked, the LAN/WiFi network is enabled to transfer statistics.

Report

Specifies the Report Interval, how frequently the Enabler reports statistics to the Mobile Device
Server.

Retransmit After
Server Contact

Specifies if the device sends statistics to the Mobile Device Server immediately following a con-
nection to the server.

Restrict Bandwidth to
User Idle Time

When enabled, periodic updates from the Mobile Device Server are postponed until the VX3Plus has
been idle for the specified period of time. The default is disabled.

Idle timeout

Specify the length of time the device must be idle before a periodic update can run, used when the
parameter above is enabled.

4-12

Summary of Contents for VX3Plus



























































































































































































































































































Reviews:

No comments