manualshive.com logo in svg

Honeywell VX3Plus, Reference Manual, Page: 201 / 282

Share
Download
Honeywell VX3Plus Reference Manual Download Page 201

Server Contact

Note:

Your VX3Plus screen display may not be exactly as shown above. Contact your

representative

for

upgrade availability and version information.

Sync Clock

Reset the time on the VX3Plus based on the time on the Mobile Device Server host PC.

Contact

On Startup – Connect to the Mobile Device Server when the Enabler is accessed.

On Resume – Connect to the Mobile Device Server when resuming from Suspend mode.

On IP Change – Connect to the Mobile Device Server when the IP address of the VX3Plus
changes.

On Ext. Power – Initiate connection to the Mobile Device Server when the device is connected to an
external power source, such as based on a docking event.

Contact Periodically /
Periodic Update

Allows the administrator to configure the Enabler to contact the Mobile Device Server and query for
updates at a regular interval beginning at a specific time.

Wakeup device if sus-
pended

If the time interval for periodic contact with the Mobile Device Server occurs, a mobile device that is
in Suspend Mode can wakeup and process updates.

Reboot before attempt

Reboot mobile device before attempting to contact Mobile Device Server.

Require external power Only connect when the mobile device has external power.

Use relative offset

Dimmed.

4-11

Summary of Contents for VX3Plus



























































































































































































































































































Reviews:

No comments