manualshive.com logo in svg

Honeywell VX3Plus, Reference Manual, Page: 171 / 282

Share
Download
Honeywell VX3Plus Reference Manual Download Page 171

Barcode Processing Examples

The following table shows examples of stripping and prefix/suffix configurations. The examples assume that the scanner is
configured to transmit a Code ID and the proper Custom IDs have been configured.

Symbology

All

EAN-128(]C1)

EAN-13(]E0)

Intrlv 2 of 5(]IO)

Code93

Enable

Enabled

Enabled

Enabled

Enabled

Disabled

Min length

1

4

1

1

Max length

all

all

all

10

Strip Code ID

Enabled

Enabled

Disabled

Enabled

Strip Leading

3

0

3

3

Strip Barcode Data

*123

1*

456

Strip Trailing

0

0

3

3

Prefix

aaa

bbb

ccc

ddd

Suffix

www

xxx

yyy

zzz

Provided that the wedge is configured with the above table, below are examples of scanned barcode data and results of these
manipulations.

Barcode Symbology

Raw Scanner Data

Resulting Data

EAN-128

]C11234567890123

bbb1234567890xxx

EAN-128

]C111234567890123

bbb11234567890xxx

EAN-128

]C1123

< rejected > (too short)

EAN-13

]E01234567890987

ccc]E04567890yyy

EAN-13

]E01231234567890987

ccc]E0234567890yyy

EAN-13

]E01234

ccc]E0yyy

I2/5

]I04444567890987654321

< rejected >

(too long)

I2/5

]I04444567890123

ddd7890zzz

I2/5

]I0444

dddzzz

I2/5

]I022245622

ddd45zzz

Code-93

]G0123456

< rejected >

(disabled)

Code-93

]G0444444

< rejected >

(disabled)

Code-39

]A01234567890

aaa4567890www

Code-39 full ASCII

]A41231234567890

aaa1234567890www

Code-39

]A4

< rejected >

(too short)

Note:

Rejected barcodes generate a bad scan beep. In some cases, the receipt of data from the scanner

triggers a good scan beep (from the external scanner), and then the rejection of scanned barcode data
by the processing causes a bad scan beep on the same data.

3-131

Summary of Contents for VX3Plus



























































































































































































































































































Reviews:

No comments