Honeywell VX3Plus Reference Manual Download Page 111

Page: 111 / 282

Using Bluetooth

Start > Settings > Control Panel > Bluetooth or Bluetooth icon in taskbar or Bluetooth icon on desktop

Bluetooth taskbar icon

The VX3Plus default Bluetooth setting is Enabled.

The VX3Plus Bluetooth

module is designed to Discover and pair with nearby Bluetooth devices.

Prerequisite

: The Bluetooth devices have been setup to allow them to be “Discovered” and “Connected/Paired”. The System

Administrator is familiar with the pairing function of the Bluetooth devices.

Bluetooth Devices Display - Before Discovering Devices

Note:

When

Filtered Mode

is enabled, only certain Bluetooth printers or Bluetooth scanners/imagers are

recognized and displayed in the Bluetooth panel. All other Bluetooth devices are ignored.

Initial Configuration

1. Select

Start > Settings > Control Panel > Bluetooth

or tap the Bluetooth icon in the taskbar or on the desktop.

2. Tap the

Settings

Tab.

3. Change the

Computer Friendly Name

at the bottom of the Settings display. The Bluetooth VX3Plus default name is

determined by the factory installed software version. Honeywell strongly urges assigning every VX3Plus a unique name
(up to 32 characters) before Bluetooth Discovery is initiated.

4. Check or uncheck the VX3Plus Bluetooth options on the

Settings

and

Reconnect

tabs.

5. Tap the OK button to save your changes or the X button to discard any changes.

3-71

Summary of Contents for VX3Plus



























































































































































































































































































Search results

Summary of Contents for VX3Plus

Reviews:

Honeywell VX3Plus, Reference Manual, Page: 111 / 282

Search results

Summary of Contents for VX3Plus

Reviews: