Honeywell Vuquest 3330g User Manual Download Page 92

Page: 92 / 201

7 - 8

NEC 2 of 5

< Default All NEC 2 of 5 Settings >

NEC 2 of 5 On/Off

Check Digit

No Check Digit

indicates that the scanner reads and transmits bar code data with or without a check digit.

When Check Digit is set to

Validate, but Don’t Transmit

, the unit only reads NEC 2 of 5 bar codes printed with a check

digit, but will not transmit the check digit with the scanned data.

When Check Digit is set to

Validate and Transmit

, the scanner only reads NEC 2 of 5 bar codes printed with a check digit,

and will transmit this digit at the end of the scanned data.

Default = No Check Digit.

Maximum Message Length

* On

Off

* No Check Digit

Validate, but Don’t Transmit

Validate and Transmit

Summary of Contents for Vuquest 3330g










































































































































































































Search results

Summary of Contents for Vuquest 3330g

Reviews:

Brands by name

Popular brands

Honeywell Vuquest 3330g, User Manual

Search results

Summary of Contents for Vuquest 3330g

Reviews:

Brands by name

Popular brands