manualshive.com logo in svg

Honeywell Vuquest 3330g, User Manual

Share
Download
Honeywell Vuquest 3330g User Manual Download Page 102

7 - 18

Telepen

<Default All Telepen Settings>

Telepen On/Off

Telepen Output

Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII 
(start/stop pattern 1).  When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and 

decodes them as compressed numeric with optional full ASCII (start/stop pattern 2).  

Default = AIM Telepen Output.

Telepen Message Length

Scan the bar codes below to change the message length.  Refer to 

Message Length Description

 (page 7-1) for additional 

information.  Minimum and Maximum lengths = 1-60.   Minimum Default = 1, Maximum Default = 60.

On

*  Off

*  AIM Telepen Output

Original Telepen Output

Minimum Message Length

Maximum Message Length

Summary of Contents for Vuquest 3330g










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands