Honeywell Voyager GS 9590 Series User Manual Download Page 9

Page: 9 / 52

NTRODUCTION

Cable Installation and Removal

Installation

Important: If the cable is not fully latched, the unit can power intermittently.

Figure 2. Connecting the Cable

1. Plug the 10-pin RJ45 end of the cable into the 10-pin socket on the scanner.

There will be an audible

click

when the connector lock engages.

2. Gently pull on the cable strain relief to insure the cable is securely installed.

Removal

Before removing the cable from the scanner, Honeywell recommends that power
to the host system be turned off. If the cable is a PowerLink cable, disconnect
the power supply on the cable.

Figure 3. Releasing the Cable

1. Locate the small

dimple

on the handle of the unit near the cable connection.

2. Bend an ordinary paperclip into the shape shown above in

Figure 3

3. To release the cable lock, push the end of the paperclip through the rubber

on the handle where the

dimple is located

4. There will be an audible

click

when the connector lock releases. Pull gently

on the strain-relief of the cable to separate the cable from the scanner.

Summary of Contents for Voyager GS 9590 Series





















































Search results

Summary of Contents for Voyager GS 9590 Series

Reviews:

Related manuals for Voyager GS 9590 Series

Brands by name

Popular brands

Honeywell Voyager GS 9590 Series, User Manual

Search results

Summary of Contents for Voyager GS 9590 Series

Reviews:

Related manuals for Voyager GS 9590 Series

Brands by name

Popular brands