manualshive.com logo in svg

Honeywell Voyager 1400g Series, User Manual, Page: 94 / 216

Share
Download
Honeywell Voyager 1400g Series User Manual Download Page 94

6 - 14

Code 93

< Default All Code 93 Settings >

Code 93 On/Off

Code 93 Message Length

Scan the bar codes below to change the message length.  Refer to 

Message Length Description

 (page 6-2) for additional information.  Mini-

mum and Maximum lengths = 0-80.  Minimum Default = 0, Maximum 
Default = 80.

Code 93 Append

This function allows the scanner to append the data from several Code 93 
bar codes together before transmitting them to the host computer.  When 
this function is enabled, the scanner stores those Code 93 bar codes that 
start with a space (excluding the start and stop symbols), and does not 
immediately transmit the data.  The scanner stores the data in the order in 

*  On

Off

Minimum Message Length

Maximum Message Length

Summary of Contents for Voyager 1400g Series

























































































































































































































Reviews:

No comments