manualshive.com logo in svg

Honeywell Voyager 1400g Series, User Manual, Page: 131 / 216

Share
Download
Honeywell Voyager 1400g Series User Manual Download Page 131

6 - 51

mined by information encoded in those bar codes.  Once the proper num-
ber of codes is reached, the data is output in the order specified in the bar 
codes.  

Default = On.

Data Matrix Code Page

Data Matrix Code pages define the mapping of character codes to charac-
ters.  If the data received does not display with the proper characters, it may 
be because the bar code being scanned was created using a  code page 
that is different from the one the host program is expecting.  If this is the 
case, scan the bar code below, select the code page with which the bar 
codes were created (see 

ISO 2022/ISO 646 Character Replacements

 on 

page A-10), and scan the value and the 

Save

 bar code from the 

Programming Chart

 on the inside the back cover of this manual.  The data 

characters should then appear properly.

Off

* On

Data Matrix Code Page

Summary of Contents for Voyager 1400g Series

























































































































































































































Reviews:

No comments