background image

 

MAN0984_Iss 4_01/19 

 

Touchpoint Plus 

Pt. No. 3011M5001 

15 

Technical Handbook 

2.1.2 Safety Hazards (Cont.) 

The following general hazards are associated with the use of this equipment: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

WARNING   DO NOT USE WATER 

DO NOT USE WATER

 if a lithium battery overheats or burns, as it may make the fire worse and it may cause 

an explosion. 

Evacuate the area immediately and call Emergency Services. 

CAUTION   HEALTH AND ENVIRONMENTAL HAZARDS 

This equipment contains a number of potentially toxic substances that may pose a health or environmental 

hazard if exposed to very high temperatures, VOCs or corrosives, or if improperly handled or disposed of. 

WARNING   FIRE OR EXPLOSION HAZARD 

Batteries may explode if mistreated. Do not disassemble them or dispose of in fire. 

CAUTION   RISK OF INJURY OR DAMAGE 

Always follow a Safe System of Work when carrying out any work involving Safety Systems. 

CAUTION   RISK OF EQUIPMENT DAMAGE 

Touchpoint Plus houses static-sensitive components. Always isolate power and discharge circuits before 

touching internal components. Always take anti-static precautions. 

CAUTION   RISK OF HEARING DAMAGE 

Touchpoint Plus can be used to control loud alarms and sirens. Always wear hearing protection when 

working in the vicinity of loud or high-pitched noises. 

CAUTION   RISK OF EYE INJURY 

Touchpoint Plus uses high energy AC and DC currents that may cause arcing and sparks if shorted out. 

Always wear eye protection when the enclosure is open. 

CAUTION   RISK OF INJURY AND DAMAGE 

Each Touchpoint Plus enclosure is heavy and weighs considerably more when packed. Ensure that a Manual 

Handling Risk Assessment is carried out before moving or installing the system, and ensure that enclosures 

are fitted securely to a suitable vertical surface. Do not place objects on the enclosures. 

Summary of Contents for Touchpoint Plus































































































































































Reviews: