manualshive.com logo in svg

Honeywell Thor VM3, User Manual, Page: 134 / 378

Share
Download
Honeywell Thor VM3 User Manual Download Page 134

122

Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide

Apply Touch Screen Protective Film

The optional Thor VM3 touch screen protective film is shipped in packs of 10. The pro-
tective film is flexible and treated with an anti-glare coating on the outer surface.

Installation

1. Make sure the touch screen is clean and dry before installation. See 

Cleaning

 for 

instructions on suitable cleaning agents.

2. Pull the release tab to separate the protective backing from the rear of the protective 

film. Avoid touching the rear side of the protective film while removing the liner.

3. Place the rear side of the protective film against the Thor VM3 display, roughly 

centering the protective film over the display.

4. Slide the protective film until one corner can be slid back between the touch screen 

and the display housing as the protective film is re-centered on the display. It may 
be necessary to press the edges of the protective film against the display to ensure 
the entire edge slides under the display housing. It is easiest to start with one of the 
bottom corners.

5. Slide the protective film away from the other bottom corner. The film may bulge 

slightly away from the Thor VM3 as it is being slid. Only slide the protective film 
enough so that the protective film can slide under the display housing on that 
corner when the protective film is returned to center. 

6. Repeat with each of the top corners, sliding the protective film away from the corner 

just enough that the protective film can slide under the display housing when the 
protective film is returned to center.

7. It may be necessary to flex the protective film during the install, however use care 

not to flex the protective film so much that the protective film kinks.

8. Once all corners are secure under the display housing, adjust the protective film, if 

necessary, so it is centered on the touch screen.

The protective film is slightly larger than 
the Thor VM3 touch screen, however the 
notches on the edge of the protective 
film (indicated by the arrows) corre-
spond to the display size of the Thor 
VM3. The protective film is not adhesive. 
The corner edges are designed to fit 
between the Thor VM3 display and the 
display housing to hold the protective 
film in place.

A protective backing is applied to the 
rear surface of the protective film. A pull 
tab is attached to the protective backing 
for easy removal of the protective back-
ing from the film.

Pull Tab

Summary of Contents for Thor VM3



























































































































































































































































































































































































Reviews:

No comments